Building Code and Building Construction - Questions and Answers
Or when you want to know how construction is supposed to be done.

|
AskCodeMan.com
|
The following Codemen are available to answer your questions:
All Codes and Standards - Jerry Peck, Codeman


Q&A Board links
  • REGISTER

  • FAQ

  • LOGIN

  • Q&A BOARD INDEX

  • View New Questions

  • View Unanswered Questions

  • View Active Questions/Answers

  • Mark Questions as read

  • View Your Questions

  • Go To Your User Control Panel




  • Links to:
  • Construction Litigation Consultants


  • Florida Building Commission

  • Florida Building Codes Online


  • International Code Council

  • ICC Codes Free Online


  • Building Officials and Administrators of Florida




  • Product Approvals
  • Florida Product Approval

  • ICC Evaluation Reports Search

  • Miami-Dade NOA Search




  • Inspector and Contractor License Search
  • Search Florida Licenses




  • Technical links
  • Technical Information page


























































  • Contact Codeman



  • Custom Search

    Use of plywood for interior of garage

    Use of plywood for interior of garage

    New postby Jim Guss on Sat Oct 23, 2010 2:34 pm

    Hello Codeman,

    I own a raised ranch type home. There are bedrooms above the garage and two walls share the interior living space. I know that code requires 5/8 drywall for the ceiling and at least the two walls that share the living space. I believe that since there is living space above the garage that the other two walls require 5/8 drywall as well but I am not sure.

    I want to remove the existing drywall due to damage and replace. What I want to know is can use 1/2 plywood directly on the studs and then attach exterior grade fiber cement 4x8 sheets on top of the plywood. I only want to do this for the walls and keep 5/8 drywall on the ceiling. This in my opinion would still give me the fire resistance they are looking for. Do you know if this would be considered acceptable? I live in Illinois...specifically Cook County.

    Thanks,
    Jim
    Jim Guss
     
    Posts: 1
    Joined: Sat Oct 23, 2010 2:16 pm

    Re: Use of plywood for interior of garage

    New postby Jerry Peck - Codeman on Sat Oct 23, 2010 9:21 pm

    I will give what I know is typical around the country, and contact someone who is much more familiar with Cook County codes than I am.

    First, the walls and structure supporting the living space above the garage would need to have 1/2" drywall on them on the garage side. Cook County may require 5/8" Type X on the wall and structure supporting the living space above - I will let my contact from Cook County address that.

    Second, the ceiling would need to have 5/8" Type X drywall on the garage side.

    Replacing the 1/2" drywall (or 5/8" Type X drywall as required) with plywood (or OSB, or any wood surface) would be a definite no go.

    I am forwarding this question to a person more knowledgeable about the codes in Cook County.
    Jerry Peck - CodeMan
    AskCodeMan.com

    Construction and Litigation Consultant
    Construction Litigation Consultants, LLC.
    ConstructionLitigationConsultants.com
    User avatar
    Jerry Peck - Codeman
    Site Admin
     
    Posts: 1089
    Joined: Fri Dec 12, 2008 12:06 pm

    Re: Use of plywood for interior of garage

    New postby markus on Sun Oct 24, 2010 12:22 pm

    Hi Jim, there are a few options as an answer to your question. Under Section 4(13-96-290)a of the City of Chicago Code, 1 hour fire separation is required. There are also various requirements for the door as well.
    Depending on whether you are in the City or suburbs there will be some variance in the requirements. Most suburbs in Cook County are under some version/year of the IRC, a few are still under UBC, and I ran into a few a couple of years ago that were working on going from BOCA (think that was it) to the IRC. As you can tell there isn't absolute uniformity in adoption. You could contact your local building dept. and ask which Code they have adopted. For your purposes however, I would go with the 1 hour rating as a baseline.
    Putting plywood under drywall in garages is a common practice by woodworkers, handyman, weekend DIY warriors. It gives them backing in order to hang stuff pretty much anywhere and keeps drywall from breaking upon typical impact. This installation has been approved by City inspectors when covered with 5/8" drywall.
    You stated your desire to use 'fiber cement board'. I'm guessing you are talking about either durock, wonderboard or hardie backer board. These would be an option but you would need to verify fire rating per thickness of each board. It's sunday morning so I haven't had a chance to look this up, from what I remember 1/2 cement board was compliant. I vaguely remember that there was an issue with hardie board though. A critical factor in all of this would be that all seams would have to be fully mudded and taped to have a complete fire rating.
    If damage resistance is what you are looking for, you may want to consider impact resistant drywall. USG makes such a product and it works really great. I've used it on jobs in the past. It will definitely take a beating. Taping out seams would also be easier. The big box stores could probably order it for you. However you would be best off finding a local drywall supply house, they tend to stock it. There are various in the City and suburbs. These places typically sell quantity to tradesman but will sell to homeowners no problem.
    I hope that helps. Feel free to ask further questions.
    Markus
    markus
     
    Posts: 4
    Joined: Thu Sep 02, 2010 9:04 am
    Location: Chicago, IL


    Return to Fire-rated assemblies: Fire walls, fire partitions, smoke barriers, ceiling-floor, ceiling-attic; Separation of garages from dwelling unit; Separation between structure's exterior walls and property line



    Who is online

    Users browsing this forum: No registered users and 1 guest



    www.AskCodeMan.com
    cron