Building Code and Building Construction - Questions and Answers
Or when you want to know how construction is supposed to be done.

|
AskCodeMan.com
|
The following Codemen are available to answer your questions:
All Codes and Standards - Jerry Peck, Codeman


Q&A Board links
  • REGISTER

  • FAQ

  • LOGIN

  • Q&A BOARD INDEX

  • View New Questions

  • View Unanswered Questions

  • View Active Questions/Answers

  • Mark Questions as read

  • View Your Questions

  • Go To Your User Control Panel




  • Links to:
  • Construction Litigation Consultants


  • Florida Building Commission

  • Florida Building Codes Online


  • International Code Council

  • ICC Codes Free Online


  • Building Officials and Administrators of Florida




  • Product Approvals
  • Florida Product Approval

  • ICC Evaluation Reports Search

  • Miami-Dade NOA Search




  • Inspector and Contractor License Search
  • Search Florida Licenses




  • Technical links
  • Technical Information page


























































  • Contact Codeman



  • Custom Search

    Approved Fastener Types and Methods

    Approved Fastener Types and Methods

    New postby pbennett1 on Sun Dec 26, 2010 10:48 pm

    Jerry, I inspected a condo with roofing nails and drywall/sheetrock screws, both with exposed heads, attached to the roof decking. What would be acceptable and unacceptable fasteners and methods?

    Thanks,
    Peter from The Blizzard State of NJ
    pbennett1
     
    Posts: 12
    Joined: Tue May 12, 2009 7:30 pm

    Re: Approved Fastener Types and Methods

    New postby Jerry Peck - Codeman on Mon Dec 27, 2010 8:25 pm

    Hi Peter,

    First, a question: Are you sure it was attached to the roof decking and not something else?

    That in and of itself is a problem. How thick is the roof decking - the standard drywall nails/screws are going to penetrate any reasonably decent thickness of roof decking, and that would create great potential for leaks. By "reasonably decent thickness of roof decking" I am referring to 1/2", 5/8" or even 3/4" roof decking - if the roof decking was over 1" that *might* work, but even then, the nails/screws might penetrate through the roof decking.

    The nails you are referring to as roofing nails are likely drywall nails as they also have a large head, although roofing nails are typically galvanized and drywall nails are typically blued, both to resist corrosion.

    The pattern varies depending on whether you are looking at a wall or a ceiling (nails need to be closer together on the ceiling than on the wall), and whether or not you are looking at drywall nails or drywall screws (nails need to be closer together than screws).

    If nails and screws are mixed, then the pattern needs to be the closer spaced pattern required for nails - I should clarify that statement: *IF* the screws meet the screw pattern, or *IF* the nails meet the nail pattern, then intermixing them does not harm, however, *IF* the screws do not meet the screw pattern, installing nails between the screws does *not* make up the difference (unless enough nails were added that the nails meet the nail pattern).
    Jerry Peck - CodeMan
    AskCodeMan.com

    Construction and Litigation Consultant
    Construction Litigation Consultants, LLC.
    ConstructionLitigationConsultants.com
    User avatar
    Jerry Peck - Codeman
    Site Admin
     
    Posts: 1089
    Joined: Fri Dec 12, 2008 12:06 pm


    Return to Drywall / gypsum board: non-fire resistance rated; Type X fire-resistance rated; plaster board (blue board); rock lath (for plastering); exterior gypsum sheathing



    Who is online

    Users browsing this forum: No registered users and 2 guests



    www.AskCodeMan.com