Building Code and Building Construction - Questions and Answers
Or when you want to know how construction is supposed to be done.

|
AskCodeMan.com
|
The following Codemen are available to answer your questions:
All Codes and Standards - Jerry Peck, Codeman


Q&A Board links
  • REGISTER

  • FAQ

  • LOGIN

  • Q&A BOARD INDEX

  • View New Questions

  • View Unanswered Questions

  • View Active Questions/Answers

  • Mark Questions as read

  • View Your Questions

  • Go To Your User Control Panel




  • Links to:
  • Construction Litigation Consultants


  • Florida Building Commission

  • Florida Building Codes Online


  • International Code Council

  • ICC Codes Free Online


  • Building Officials and Administrators of Florida




  • Product Approvals
  • Florida Product Approval

  • ICC Evaluation Reports Search

  • Miami-Dade NOA Search




  • Inspector and Contractor License Search
  • Search Florida Licenses




  • Technical links
  • Technical Information page


























































  • Contact Codeman



  • Custom Search

    Upside Down Panels

    Upside Down Panels

    New postby Timham on Wed Jun 28, 2017 7:10 pm

    Hi Jerry,
    I have had three replacement distribution panels installed upside down in the last 2 days. This results in circuit #1 in the lower right corner and 36-40 at the top left. Any thoughts, as a previous municipal inspector?
    Thanks, as always, for your years of expert advise!
    Timham
     
    Posts: 6
    Joined: Thu Dec 15, 2016 10:10 pm

    Re: Upside Down Panels

    New postby Jerry Peck - Codeman on Wed Jun 28, 2017 8:26 pm

    Tim,

    Look inside the panels and either stamped into or stamped onto the back of the panels will be something which states which is up and which is down, and typically you will find something which states as shown in the photos below.

    The panel which states "TOP" is, obviously, stating which way the panel enclosure is intended to be installed to be installed.

    The panel which states LINE/LINE (with one upside down below the rightside up one) is indicating that the panel enclosure may be installed with either end up or down. Provided that the panelboard itself is securely fastened in place in the enclosure in the manner in which the manufacturer intended, then that panelboard is designed to have the feed come in at the top or at the bottom.

    Some are designed and intended to be installed one way, others are designed and intended to be installed either end up.

    In a panelboard which is properly installed in an enclosure which is permitted to be installed either end up, and if the panelboard is not 'centered' vertically in the enclosure, then when the cover is installed, the cover may need to be installed 'upsidedown', which would make the circuit numbers upsidedown too. However, the circuit numbers are just there to identify the breaker to the label which identifies 'what the breaker is for'.

    I have seen a few which I could accurately report as being installed "upsidedown', however, most/many do not have an 'up' or a 'down' ... 'installed horizontally' with the breakers operating vertically - absolutely incorrect ... 'installed with the back against a ceiling' - also absolutely incorrect (I have seen many of these) ... installed with the back against a floor or cabinet' - also absolutely incorrect (I have only seen this done once or twice).

    Panel UP-DOWN 02.jpg


    Panel UP-DOWN 01.jpg
    You do not have the required permissions to view the files attached to this post.
    Jerry Peck - CodeMan
    AskCodeMan.com

    Construction and Litigation Consultant
    Construction Litigation Consultants, LLC.
    ConstructionLitigationConsultants.com
    User avatar
    Jerry Peck - Codeman
    Site Admin
     
    Posts: 1059
    Joined: Fri Dec 12, 2008 12:06 pm


    Return to Electrical: Service Equipment, electrical panels, wiring, lighting, switches, receptacles, etc.



    Who is online

    Users browsing this forum: No registered users and 1 guest



    www.AskCodeMan.com