Building Code and Building Construction - Questions and Answers
Or when you want to know how construction is supposed to be done.

|
AskCodeMan.com
|
The following Codemen are available to answer your questions:
All Codes and Standards - Jerry Peck, Codeman


Q&A Board links
  • REGISTER

  • FAQ

  • LOGIN

  • Q&A BOARD INDEX

  • View New Questions

  • View Unanswered Questions

  • View Active Questions/Answers

  • Mark Questions as read

  • View Your Questions

  • Go To Your User Control Panel




  • Links to:
  • Construction Litigation Consultants


  • Florida Building Commission

  • Florida Building Codes Online


  • International Code Council

  • ICC Codes Free Online


  • Building Officials and Administrators of Florida




  • Product Approvals
  • Florida Product Approval

  • ICC Evaluation Reports Search

  • Miami-Dade NOA Search




  • Inspector and Contractor License Search
  • Search Florida Licenses




  • Technical links
  • Technical Information page


























































  • Contact Codeman



  • Custom Search

    Lintel Sag Formula

    Lintel Sag Formula

    New postby pbennett1 on Sun Jun 27, 2010 11:57 am

    Hey Jerry,
    Is there a formula for allowable tolerance of a sagging steel lintel?
    You do not have the required permissions to view the files attached to this post.
    pbennett1
     
    Posts: 12
    Joined: Tue May 12, 2009 7:30 pm

    Re: Lintel Sag Formula

    New postby Jerry Peck - Codeman on Sun Jun 27, 2010 2:48 pm

    The answer is: It depends.

    As in "it depends" on a variety of things. Such as: the species of the lumber, the use, the live load, the dead load, if engineered (such as LVL, I-joist, etc.), and other conditions.

    Typical deflection limits, for a sampling of various conditions, might be 1/180, 1/240, or 1/360.

    As example, let us take 1/240 ... that means the maximum deflection is 1/240 of the span, if the span is 16 feet (presuming a 16 foot wide garage opening), then the deflection could be 16 feet X 12 inches = 192 inches / 240 = 0.8 inches, or just over 3/4" deflection under a specific set of conditions which would allow for a 1/240 deflection.

    How much is allowed in your case? I do not know, however, if you take the maximum deflection allowed for almost any condition ... 1/180 ... and use that, if that is exceeded than ... more than likely ... more than likely it would be a problem. So, let's do the above example using 1/180:
    - Using 1/180 with a span of 16 feet, then the deflection could be 16 feet X 12 inches = 192 inches / 180 = 1.06 inches, or just over 1" deflection under conditions which would allow for a 1/180 deflection.
    - If it sags (deflects) more than 1 inch for a 16 foot span then it is highly likely that there is a problem as that would exceed the most generous deflection allowance.
    Jerry Peck - CodeMan
    AskCodeMan.com

    Construction and Litigation Consultant
    Construction Litigation Consultants, LLC.
    ConstructionLitigationConsultants.com
    User avatar
    Jerry Peck - Codeman
    Site Admin
     
    Posts: 1101
    Joined: Fri Dec 12, 2008 12:06 pm

    Re: Lintel Sag Formula

    New postby pbennett1 on Sun Jun 27, 2010 3:17 pm

    Thanks for both replies.
    I will be going back tomorrow to retrieve the radon canister.
    I did not take any measurements, but just "eyed" it up. The gap between the mortar joint and seems uniform in size, so I really think the "sag" maybe just shrinking mortar, thus an illusion.
    PB
    pbennett1
     
    Posts: 12
    Joined: Tue May 12, 2009 7:30 pm


    Return to Exterior Clading: brick veneer; stucco; siding - vinyl, wood, cementitious (such as HardiePlank), hardboard (such as Masonite siding); EIFS



    Who is online

    Users browsing this forum: No registered users and 1 guest



    www.AskCodeMan.com
    cron